crumb.isLink crumb.isFinalCrumb crumb.getClass crumb.css crumb.separatorCss crumb.getCss crumb.finalCrumb crumb.getText crumb.getIsLink crumb.getWrapperCss crumb.type crumb.url crumb.getUrl crumb.getType crumb.hashCode crumb.equals crumb.toString crumb.wrapperCss crumb.text crumb.getSeparatorCss crumb.class
crumb.isLink crumb.isFinalCrumb crumb.getClass crumb.css crumb.separatorCss crumb.getCss crumb.finalCrumb crumb.getText crumb.getIsLink crumb.getWrapperCss crumb.type crumb.url crumb.getUrl crumb.getType crumb.hashCode crumb.equals crumb.toString crumb.wrapperCss crumb.text crumb.getSeparatorCss crumb.class
crumb.isLink crumb.isFinalCrumb crumb.getClass crumb.css crumb.separatorCss crumb.getCss crumb.finalCrumb crumb.getText crumb.getIsLink crumb.getWrapperCss crumb.type crumb.url crumb.getUrl crumb.getType crumb.hashCode crumb.equals crumb.toString crumb.wrapperCss crumb.text crumb.getSeparatorCss crumb.class
crumb.isLink crumb.isFinalCrumb crumb.getClass crumb.css crumb.separatorCss crumb.getCss crumb.finalCrumb crumb.getText crumb.getIsLink crumb.getWrapperCss crumb.type crumb.url crumb.getUrl crumb.getType crumb.hashCode crumb.equals crumb.toString crumb.wrapperCss crumb.text crumb.getSeparatorCss crumb.class
08.12.2018 17:43 Zuletzt bearbeitet: 08.12.2018 17:47 durch den Autor
Hallo,
wir haben unserer Tarif verbessert. Es war früh 50/10, jetzt ist es schneller - 100\40.
Mit dem alten Tarif hat Cisco 886VA gut finktioniert, aber mit dem neuen Tarif geht es nur mit der Geschwindigkeit 16/1.6 Mbps.
Ich frage mich, ob der Cisco 886VA 100/40 unterstützt. Wenn ja, was ich dafür änderen muss?
Meine Einstellungen:
! controller VDSL 0 ! interface Ethernet0 description WAN no ip address ip nbar protocol-discovery ipv4 service-policy input Hosts ! interface Ethernet0.7 description VDSL VLAN 7 tagged encapsulation dot1Q 7 pppoe enable group global pppoe-client dial-pool-number 1 !
interface Vlan1
description LAN
ip address 10.254.1.1 255.255.255.0
ip mtu 1492
ip nbar protocol-discovery ipv4
ip flow ingress
ip nat inside
ip virtual-reassembly in max-reassemblies 64
! interface Dialer0 description VDSL TELEKOM ip ddns update hostname office.dyndns.org ip ddns update dyndns ip address negotiated no ip redirects no ip unreachables no ip proxy-arp ip mtu 1492 ip nbar protocol-discovery ipv4 ip nat outside ip virtual-reassembly in encapsulation ppp ip tcp adjust-mss 1452 load-interval 30 dialer pool 1 dialer-group 1 no keepalive ppp authentication pap callin ppp pap sent-username ***********************@t-online.de password 7 ********************** ppp ipcp dns request ppp ipcp mask request ppp ipcp route default no cdp enable ! ip nat inside source list 101 interface Dialer0 overload access-list 101 permit ip 10.254.1.0 0.0.0.255 any access-list 101 permit ip 10.254.2.0 0.0.0.255 any
!
sh ver
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 04-Aug-15 05:50 by prod_rel_team
ROM: System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1)
office.dyndns.org uptime is 1 hour, 51 minutes
System returned to ROM by reload at 15:24:18 UTC Sat Dec 8 2018
System restarted at 15:53:02 UTC Sat Dec 8 2018
System image file is "flash:c800-universalk9-mz.SPA.153-3.M6.bin"
!
sh controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xC055
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FCZ2044B08C C886VA-K 15.3(3)M6
Serial Number Far: eq nr port:23 oemid softwarerev
Modem Version Near: 15.3(3)M6
Modem Version Far: 0xc055
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 17a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 0 0
Line Attenuation: 0.0 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 6.3 dB 10.7 dB
Attainable Rate: 16600 kbits/s 1614 kbits/s
Actual Power: 1.4 dBm 11.4 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 7.5 N/A N/A 4.9 N/A N/A N/A
Signal Attenuation(dB): 7.5 N/A N/A 4.9 N/A N/A N/A
Noise Margin(dB): 6.3 N/A N/A 10.7 N/A N/A N/A
Total FECC: 266 0
Total ES: 4 0
Total SES: 4 0
Total LOSS: 3 0
Total UAS: 1464 1464
Total LPRS: 0 0
Total LOFS: 3 0
Total LOLS: 0 0
Full inits: 2
Failed full inits: 0
Short inits: 0
Failed short inits: 1
Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 130205_1433-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Vendor Version: Bpv35j.23j 68
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 16331 0 1576
SRA Previous Speed: 0 16339 0 1576
Previous Speed: 0 16339 0 1576
Reed-Solomon EC: 0 98 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 0.00 0.00 9.00
Actual INP: 2.01 29.00 0.00 1.00
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
Und die Einstellungen von Zyxel, den wir von Telekom bekommen haben, und der 100\40 unterstützt:
!
Statusübersicht
Hier sehen Sie eine detaillierte Auflistung aller DSL-Status-Informationen.
DSL-Status
Leitungs-Status: Leitung verbunden
Modus: VDSL2
Kanal-Modus: EFM
Profil: Profile 17a
DSL-Verbindungsversuche: 0
DSL Modemtreiber-Version: 8.11.2.6.0.7
Übertragungsgeschwindigkeit
Upstream Downstream
Aktuelle Daten-Rate: 34967 Kbit/s 102784 Kbit/s
Leitungskapazität: 37378 Kbit/s 133339 Kbit/s
Betriebsdaten / Fehleranzeige
Upstream Downstream
Signal-Rausch-Abstand (Band 0): 9 dB 11 dB
Leitungsdämpfung (Band 0): 4 dB 8 dB
Signaldämpfung (Band 0): 4 dB 8 dB
Signal-Rausch-Abstand (Band 1): 10 dB 12 dB
Leitungsdämpfung (Band 1): 12 dB 17 dB
Signaldämpfung (Band 1): 12 dB 17 dB
Signal-Rausch-Abstand (Band 2): 9 dB 12 dB
Leitungsdämpfung (Band 2): 20 dB 25 dB
Signaldämpfung (Band 2): 20 dB 25 dB
Fehlerindikatoren
Near-End-Indikator Far-End-Indikator
FEC Fehler: 0 0
CRC Fehler: 0 6
CRC_P Fehler: 0 0
CRCP_P Fehler: 0 0
CV_P Fehler: 6 0
CVP_P Fehler: 0 0
Ich debanke mich im Voraus!
Gelöst! Gehe zu Lösung.
Die Modem Firmware ist von 2016, zuerst diese aktualisieren.
Füllen Sie schnell und unkompliziert unser Online-Kontaktformular aus, damit wir sie zeitnah persönlich beraten können.
Informieren Sie sich über unsere aktuellen Internet-Angebote.