Hallo,

wir haben unserer Tarif verbessert. Es war früh 50/10, jetzt ist es schneller - 100\40.
Mit dem alten Tarif hat Cisco 886VA gut finktioniert, aber mit dem neuen Tarif geht es nur mit der Geschwindigkeit 16/1.6 Mbps.

Ich frage mich, ob der Cisco 886VA 100/40 unterstützt. Wenn ja, was ich dafür änderen muss?

Meine Einstellungen:

!
controller VDSL 0
!
interface Ethernet0
description WAN
no ip address
ip nbar protocol-discovery ipv4
service-policy input Hosts
!
interface Ethernet0.7
description VDSL VLAN 7 tagged
encapsulation dot1Q 7
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface Vlan1
 description LAN
 ip address 10.254.1.1 255.255.255.0
 ip mtu 1492
 ip nbar protocol-discovery ipv4
 ip flow ingress
 ip nat inside
 ip virtual-reassembly in max-reassemblies 64
!
interface Dialer0
description VDSL TELEKOM
ip ddns update hostname office.dyndns.org
ip ddns update dyndns
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip nbar protocol-discovery ipv4
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
load-interval 30
dialer pool 1
dialer-group 1
no keepalive
ppp authentication pap callin
ppp pap sent-username ***********************@t-online.de password 7 **********************
ppp ipcp dns request
ppp ipcp mask request
ppp ipcp route default
no cdp enable
!
ip nat inside source list 101 interface Dialer0 overload
access-list 101 permit ip 10.254.1.0 0.0.0.255 any
access-list 101 permit ip 10.254.2.0 0.0.0.255 any
!

sh ver
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 04-Aug-15 05:50 by prod_rel_team

ROM: System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1)

office.dyndns.org uptime is 1 hour, 51 minutes
System returned to ROM by reload at 15:24:18 UTC Sat Dec 8 2018
System restarted at 15:53:02 UTC Sat Dec 8 2018
System image file is "flash:c800-universalk9-mz.SPA.153-3.M6.bin"

!
sh controller vdsl 0
Controller VDSL 0 is UP

Daemon Status: Up

 XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xC055
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FCZ2044B08C C886VA-K 15.3(3)M6
Serial Number Far: eq nr port:23 oemid softwarerev
Modem Version Near: 15.3(3)M6
Modem Version Far: 0xc055

Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 17a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
SRA: disabled disabled
 SRA count: 0 0
Bit swap: enabled enabled
 Bit swap count: 0 0
Line Attenuation: 0.0 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 6.3 dB 10.7 dB
Attainable Rate: 16600 kbits/s 1614 kbits/s
Actual Power: 1.4 dBm 11.4 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 7.5 N/A N/A 4.9 N/A N/A N/A
Signal Attenuation(dB): 7.5 N/A N/A 4.9 N/A N/A N/A
Noise Margin(dB): 6.3 N/A N/A 10.7 N/A N/A N/A
Total FECC: 266 0
Total ES: 4 0
Total SES: 4 0
Total LOSS: 3 0
Total UAS: 1464 1464
Total LPRS: 0 0
Total LOFS: 3 0
Total LOLS: 0 0

Full inits: 2
Failed full inits: 0
Short inits: 0
Failed short inits: 1

Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded VDSL_LINUX_DEV_01212008 (1)

Modem  FW  Version: 130205_1433-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Vendor Version: Bpv35j.23j 68


 DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 16331 0 1576
SRA Previous Speed: 0 16339 0 1576
Previous Speed: 0 16339 0 1576
Reed-Solomon EC: 0 98 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 0.00 0.00 9.00
Actual INP: 2.01 29.00 0.00 1.00

Training Log : Stopped
Training Log Filename : flash:vdsllog.bin

Und die Einstellungen von Zyxel, den wir von Telekom bekommen haben, und der 100\40 unterstützt:

!
Statusübersicht
Hier sehen Sie eine detaillierte Auflistung aller DSL-Status-Informationen.

DSL-Status
Leitungs-Status: Leitung verbunden
Modus: VDSL2
Kanal-Modus: EFM
Profil: Profile 17a
DSL-Verbindungsversuche: 0
DSL Modemtreiber-Version: 8.11.2.6.0.7
Übertragungsgeschwindigkeit
 Upstream Downstream
Aktuelle Daten-Rate: 34967 Kbit/s 102784 Kbit/s
Leitungskapazität: 37378 Kbit/s 133339 Kbit/s
Betriebsdaten / Fehleranzeige
 Upstream Downstream
Signal-Rausch-Abstand (Band 0): 9 dB 11 dB
Leitungsdämpfung (Band 0): 4 dB 8 dB
Signaldämpfung (Band 0): 4 dB 8 dB
Signal-Rausch-Abstand (Band 1): 10 dB 12 dB
Leitungsdämpfung (Band 1): 12 dB 17 dB
Signaldämpfung (Band 1): 12 dB 17 dB
Signal-Rausch-Abstand (Band 2): 9 dB 12 dB
Leitungsdämpfung (Band 2): 20 dB 25 dB
Signaldämpfung (Band 2): 20 dB 25 dB
Fehlerindikatoren
 Near-End-Indikator Far-End-Indikator
FEC Fehler: 0 0
CRC Fehler: 0 6
CRC_P Fehler: 0 0
CRCP_P Fehler: 0 0
CV_P Fehler: 6 0
CVP_P Fehler: 0 0

Ich debanke mich im Voraus!